Fort Lauderdale Water Heater Safety

Posted by on May 9, 2014 in Water Heater Repair Fort Lauderdale

Water heaters are rather basic on the face of it, and they’ve changed little in the past 50 years suggests Water Heater Repair Fort Lauderdale. Thanks to some essential refinements, they are certainly much better than they used to be, with longer life spans, greater efficiency, and more security features that decrease the threat of injury and property damage.

All water heaters convert energy to heat, and then transfer that heat to water. They are connected to a cold water supply pipe and have at least one pipe for outgoing hot water that directs the heated water to taps and home appliances throughout the house.

Though there is a range of water heaters on the market, including electric, propane, tankless versions, as well as solar-powered models, the most usual in the United States is a holding tank fed by natural gas.

These include a steel tank with a heating element at the bottom and a flue running down the center of the tank to vent the carbon monoxide that is a by-product of burning natural gas.

You’ll also see some sort of thermostat control on the body of the tank that allows one to shut off the gas and regulate the pilot light. These thermostats use a temperature-sensing probe that automatically shuts down the gas if it detects that the pilot light goes out or fails to light.

The interior of the tank is bonded with vitreous glass to safeguard it from rusting. Despite this protective sheath, there is still some small amount of steel exposed, triggered by constraints in the covering process. That exposed steel is vulnerable to rust. To protect the steel from rusting, the makers set up sacrificial anode rods in the tanks, usually made from magnesium or aluminum. With the procedure of electrolysis, the anode rod corrodes, instead of the tank. The tank will rust if the anode rod is totally consumed, unless one replaces it. This is the most usual reason for problems with water heaters.

Preventive Maintenance and Fort Lauderdale Water Heater SafetyWater Heater Repair Fort Lauderdale

For the functions of this information, we’re willing to assume that water heater was correctly set up, and that it passed the home evaluation.

Here are some of the fundamental steps to keeping a water heater in proper shape.

Initially, eyeball it. Water heaters have a great deal of rust security within, however hardly any on the outside, so look out for leakages. Likewise inspect for staining, flaking paint, or rust on the surface of the tank. External rust can cause your tank to fail just as surely as internal rust. Remember that the outside shell may look fine on the outside, while consumed with rust on the inside. However, if nothing looks out of the ordinary, move on to routine upkeep responsibilities.

The two main steps to keeping a water heater are occasionally draining the tank to get rid of sediment, and testing the temperature level and pressure release valve (T&P valve) to make sure that it is working effectively.

When a water heater operates, sediment develops. That sediment is in fact calcium carbonate, a mineral present in the water, which is precipitated out by heating. It settles to the bottom of the storage tank, and can shorten the life of a water heater; minimize its efficiency; block valves, lines and the recirculating pump; and even offer a sanctuary for anaerobic bacteria. How typically one drains the tank depends a lot on the water quality where one lives. Locations that have very hard water need more frequent draining to keep sediment levels low. Usually, the frequency is anywhere from 6 months to 1 year.

The T&P valve is important for preventing explosions due to over-pressure, as it immediately releases water at certain vital pressure levels and avoids the tank from blowing up. Test this valve periodically to guarantee that it opens and closes effectively, so it won’t fail when you need it most.

KEEP IN MIND: If you have actually never ever carried out these tasks in the past, it’s a good idea to hire a technician to do it for you the very first time, and inquire to reveal you ways to do it yourself. While it’s not exceedingly complicated, there are possible hazards involved. The risks of doing it incorrectly are large in contrast to a very little service charge.

Finally, install a carbon monoxide gas alarm near to your water heater. Carbon monoxide is odor-free and colorless, but if your water heater does not vent properly or begins to back draft, those deadly fumes can enter the residence and jeopardize the household.

If everything is working correctly, check the water temperature with a cooking thermometer to see to it it’s set to your households’ comfort level and to guarantee security. If the water is too hot, it can scald or cause injury. Alternatively, some individuals set their water temperature level low to try to be economical. If the water isn’t hot enough, it can harbor bacteria. A great intermediate setting for your water is above 120 degrees.

Learn more tips on our other blog articles too!